![\"\"](\"https:\/\/sylaquiltartist.pl\/v1\/wp-content\/uploads\/2020\/11\/sh22.jpg\")
<\/a><\/figure>\n<\/div>\n\n\nWe have two other panels, which I will call \u201cB,\u201d that need to be cut at 60 \u02da in a similar way with one difference. In the \u201cB\u201d panels the starting point is \u00be\u201d away from the bottom left-hand corner. The first piece that is cut is \u00be\u201d wide. Throw it away. Continue with the same pattern as we did on the \u201cA\u201d panels and slice the rest of the \u201cB\u201d panels into 1.5\u201d strips.<\/p>\n\n\n
<\/a><\/figure>\n<\/div>\n\n\nWorking from left to right, the cut pieces from panel \u201cA\u201d are labeled A1, A2, A3, etc.<\/p>\n\n\n\n
Working from the left to right, the cut pieces from panel \u201cB\u201d are labeled B1, B2, B3, etc.<\/p>\n\n\n
<\/a><\/figure>\n<\/div>\n\n\nWe can arrange the panels together following the pattern of A1, B1, A2, B2, A3, B3, etc. I cut the strips having the panels upside down so my pattern was slightly different, B1, A1, B2, A2. This didn\u2019t change the design.<\/p>\n\n\n\n
This is how it looks arranged together.<\/p>\n\n\n
<\/a><\/figure>\n<\/div>\n\n\nAnd here is the back.<\/p>\n\n\n
<\/a><\/figure>\n<\/div>\n\n\nHere you can see what the guidelines were for. The strips are sown together according to the lines.<\/p>\n\n\n
<\/a><\/figure>\n<\/div>\n\n\nI drew this method out on a sheet of paper to make it clearer. Through the marked points we drag the needle with dental floss, connecting the strips. The black line in the middle is the cutting line, the red is the sewing line.<\/p>\n\n\n
<\/a><\/figure>\n<\/div>\n\n\nThe strips are sewn together on the machine using the dental floss, the floss won\u2019t damage the needle.<\/p>\n\n\n
<\/a><\/figure>\n<\/div>\n\n<\/a><\/figure>\n<\/div>\n\n\nAfter the strips are sewn, the back of panel A and panel B should look like this. Press the seams open.<\/p>\n\n\n
<\/a><\/figure>\n<\/div>\n\n\nSo, I got panel \u201cA\u201d and panel \u201cB\u201d<\/p>\n\n\n
<\/a><\/figure>\n<\/div>\n\n\nLets start working with the second set of panels \u201cA\u201d and \u201cB\u201d.<\/p>\n\n\n\n
The second panel A is cut into 1,5\u201d strips at 60 \u02daangle using the same method as before with panel A that means we start cutting process from the left lower corner. We label them A1, A2, A3 etc.<\/p>\n\n\n\n
The second panel panel B is cut into 1,5\u201d strips at 60 \u02da angle using the same method as before with panel B that means the starting point is 3\/4 \u201caway from the left lower corner. We label them B1, B2, B3 etc.<\/p>\n\n\n
<\/a><\/figure>\n<\/div>\n\n\nWe arranged strips from left to right A1, B1, A2, B2 etc. and sew them together using the same trick I shared with you on previous post, using dental floss. Here you can see the guide lines being helpful again.<\/p>\n\n\n
<\/a><\/figure>\n<\/div>\n\n\nThe face of the panel.<\/p>\n\n\n
<\/a><\/figure>\n<\/div>\n\n\nThe back of the panel. Press the seams open.<\/p>\n\n\n
<\/a><\/figure>\n<\/div>\n\n\nI cut the sewn panel and stich in a ditch with polyester thread emphasizing nice diamond shapes.<\/p>\n\n\n
<\/a><\/figure>\n<\/div>\n\n<\/a><\/figure>\n<\/div>\n\n